收藏本站
?
?
?
If bit 2 of word 86 shall be set to zero, the Drive does not support the CFA feature set.
If bit 3 of word 86 is set to one, the Advanced Power Management feature set has been enabled via the
Set Features command.
Bit 4 of word 86 shall be set to zero; the Drive does not support the Removable Media Status feature set.
6.5.28 Word 88: Ultra DMA Modes Supported and Selected
Word 88 identifies the Ultra DMA transfer modes supported by the device and indicates the mode that is
currently selected. Only one DMA mode shall be selected at any given time. If an Ultra DMA mode is selected,
then no Multiword DMA mode shall be selected. If a Multiword DMA mode is selected, then no Ultra DMA mode
shall be selected. Support of this word is mandatory if Ultra DMA is supported. Word 88 shall return a value of 0
if the device does not support UDMA.
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
Bit 15:
Bit 14: 1
Bit 13: 1
Bit 12: 1
Bit 11: 1
Bit 10: 1
Bit 9: 1
Bit 8: 1
Bit 7:
Bit 6: 1
Bit 5: 1
Bit 4: 1
Bit 3: 1
Bit 2: 1
Bit 1: 1
Bit 0: 1
Reserved
= Ultra DMA mode 6 is selected 0 = Ultra DMA mode 6 is not selected
= Ultra DMA mode 5 is selected 0 = Ultra DMA mode 5 is not selected
= Ultra DMA mode 4 is selected 0 = Ultra DMA mode 4 is not selected
= Ultra DMA mode 3 is selected 0 = Ultra DMA mode 3 is not selected
= Ultra DMA mode 2 is selected 0 = Ultra DMA mode 2 is not selected
= Ultra DMA mode 1 is selected 0 = Ultra DMA mode 1 is not selected
= Ultra DMA mode 0 is selected 0 = Ultra DMA mode 0 is not selected
Reserved
= Ultra DMA mode 6 and below are supported. Bits 0-5 shall be set to 1.
= Ultra DMA mode 5 and below are supported. Bits 0-4 shall be set to 1.
= Ultra DMA mode 4 and below are supported. Bits 0-3 shall be set to 1.
= Ultra DMA mode 3 and below are supported, Bits 0-2 shall be set to 1.
= Ultra DMA mode 2 and below are supported. Bits 0-1 shall be set to 1.
= Ultra DMA mode 1 and below are supported. Bit 0 shall be set to 1.
= Ultra DMA mode 0 is supported
6.5.29 Word 89: Time required for Security erase unit completion
Word 89 specifies the time required for the SECURITY ERASE UNIT command to complete. Support of this word is
mandatory if the Security feature set is supported.
Required Time=(Value*2) minutes
6.5.30 Word 92: Master Password Revision Code
Word 92 contains the value of the Master Password Revision Code set when the Master Password was last
changed. Valid values are 0001h through FFFEh. A value of 0000h or FFFFh indicates that the Master
Password Revision is not supported. Support of this word is mandatory if the Security feature set is
supported.
6.5.31 Word 128: Security status
Support of this word is mandatory if the Security feature set is supported.
Bit 8 of word 128 indicates the security level. If security mode is enabled and the security level is high, bit 8
shall be cleared to zero. If security mode is enabled and the security level is maximum, bit 8 shall be set to
one. When security mode is disabled, bit 8 shall be cleared to zero.
Bit 5 of word 128 indicates the Enhanced security erase unit feature is supported. If bit 5 is set to one, the
Enhanced security erase unit feature set is supported.
Bit 4 of word 128 indicates that the security count has expired. If bit 4 is set to one, the security count is expired
and SECURITY UNLOCK and SECURITY ERASE UNIT are command aborted until a power-on reset or hardware
reset.
Bit 3 of word 128 indicates security frozen. If bit 3 is set to one, the security is frozen.
Bit 2 of word 128 indicates security locked. If bit 2 is set to one, the security is locked.
Bit 1 of word 128 indicates security enabled. If bit 1 is set to one, the security is enabled.
Bit 0 of word 128 indicates the Security Mode feature set supported. If bit 0 is set to one, security is supported.
Swissbit AG
Industriestrasse 4
Swissbit reserves the right to change products or specifications without notice.
Revision: 1.41
CH-9552 Bronschhofen
Switzerland
www.swissbit.com
industrial@swissbit.com
F-100_data_sheet_CA-HxBR_Rev141.doc
Page 21 of 51
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
SFCA64GBH2BV4TO-I-NU-216-STD FLASH CFAST UDMA/MDMA/PIO 64GB
SFCF2048H1BO2TO-I-M0-523-SMA FLASH SLC UDMA/MDMA/PIO 2G
SFCF4096H4BK2SA-I-QT-553-SMA FLASH SLC UDMA/MDMA/PIO 4G
SFCF64GBH2BU4TO-I-NU-517-STD FLASH SLC UDMA/MDMA/PIO 64GB
SFN08B4702CBQLF7 RES ARRAY 47K OHM 7 RES 8-DFN
SFP1050-12BG FRONT END AC/DC 1050W 12V
SFP450-12BG PWR SUP 450W 12V 36.6A W/STANDBY
SFSD1024N1BN1TO-I-DF-151-STD FLASH MICRO SD CARD IND S-200 1G
相关代理商/技术参数
SFCA16GBH1BR4TO-I-QT-236-STD 功能描述:FLASH CFAST UDMA/MDMA/PIO 16GB RoHS:是 类别:存储卡，模块 >> 存储器，PC 卡 系列:F-100 标准包装:30 系列:- 存储容量:8GB 存储器类型:存储卡 - Extreme III SD?
SFCA16GBH2BV4TO-I-QT-216-STD 功能描述:FLASH CFAST UDMA/MDMA/PIO 16GB RoHS:是 类别:存储卡，模块 >> 存储器，PC 卡 系列:F-240 标准包装:30 系列:- 存储容量:8GB 存储器类型:存储卡 - Extreme III SD?
SFCA16GBH2BV4TO-I-QT-226-STD 功能描述:Memory Card CFast 16GB SLC 制造商:swissbit na inc. 系列:F-240 零件状态:有效 存储器类型:CFast 存储容量:16GB 速度:- 技术:SLC 工作温度:-40°C ~ 85°C 标准包装:75
SFCA2048H1BV4TO-C-MS-216-STD 制造商:SWISSBIT NA INC 功能描述:FLASH
SFCA2048H1BV4TO-I-MS-216-STD 功能描述:FLASH CFAST UDMA/MDMA/PIO 2GB RoHS:是 类别:存储卡，模块 >> 存储器，PC 卡 系列:F-240 标准包装:30 系列:- 存储容量:8GB 存储器类型:存储卡 - Extreme III SD?
SFCA2048H1BV4TO-I-MS-226-STD 制造商:SWISSBIT 功能描述:CFAST F-240 DENSITY INDUSTRIAL - Trays
SFCA240GH1AA2TO-I-OC-216-STD 功能描述:Memory Card CFast 240GB MLC 制造商:swissbit na inc. 系列:F-60 零件状态:有效 存储器类型:CFast 存储容量:240GB 速度:- 技术:MLC 工作温度:-40°C ~ 85°C 标准包装:75
SFCA256GH1AD4TO-I-HT-216-STD 功能描述:MEM CARD COMPACTFLASH 256GB MLC 制造商:swissbit 系列:F-50 零件状态:在售 存储器类型:CFast 存储容量:256GB 速度:- 技术:MLC 工作温度:-40°C ~ 85°C 标准包装:1